Design and Thermomechanical Evaluation of Polymer Matrix Ablative Composite Materials for Rocket Motor Nozzles

Keywords: materials science and technology, rockets, aerospace materials, composite materials, aerospace propulsion

Abstract

Rocket propulsion systems require materials with high thermal resistance and low density for rocket-motor nozzles, where polymeric ablative composite materials (PACM) emerge as a low-cost alternative. This research aimed to design and characterize polymer matrix ablative composite materials (PACM) based on a polyester resin modified with ceramic particulates (refractory brick and quartz) and synthetic fibers (glass and carbon). The methodology included physical tests (density), mechanical tests (compression, tensile, flexural, and impact strength), thermal tests (thermogravimetric analysis, thermal conductivity, and direct flame resistance), and scanning electron microscopy. The results highlighted that PACMs exhibit densities ranging from 1.22 to 1.67g/cm³ and thermal insulation values between 83% and 90% when exposed to a propane gas flame at 1600–2000°C for 120 seconds, a condition simulating the combustion of a sounding rocket motor during a low-altitude flight. Additionally, thermo-mechanical simulation using Ansys software demonstrated that the designed PACMs can withstand the thermal conditions experienced during rocket motor combustion. However, for nozzles with a 7 mm thick ablative zone, an external carbon fiber reinforcement of 2.5 mm thickness is required to endure the mechanical stresses generated by the high exhaust pressure. In conclusion, PACMs can be employed in the manufacturing of propulsion components such as nozzles using readily available materials, which are also lighter than conventional refractory metals and superalloys, thereby contributing to the development of experimental rocketry missions in emerging countries such as Colombia.

Author Biographies

Valentina Candela-Rengifo, Universidad del Valle
Rafael Robayo-Salazar, Universidad del Valle
Julián Portocarrero Hermann, Escuela Militar de Aviación “Marco Fidel Suarez”
Gustavo Adolfo Rojas, Escuela Militar de Aviación “Marco Fidel Suarez”
Jonathan Salgado Díaz, Escuela Militar de Aviación “Marco Fidel Suarez”

References

M. Peters, and C. Leyens, “Volume III. Aerospace and Space Materials,” in Material Science and Engineering, R. D. Rawlings, Ed., New York, USA: Unesco-Encyclopedia of Life Support Systems (EOLSS), 2022. https://eolss.net/Sample-Chapters/C05/E6-36-05-03.pdf

O. Uyanna, and H. Najafi, “Thermal protection systems for space vehicles: A review on technology development, current challenges and future prospects,” Acta Astronaut., vol. 176, pp. 341-356, Nov. 2020. https://doi.org/10.1016/j.actaastro.2020.06.047

J. Portocarrero Hermann, J. D. Osorio, and R. A. Robayo-Salazar, “Ablative Composites of Polymeric Matrix (Polyester Resin) Reinforced with Industrial Residue Materials and Fiberglass,” Rev. Ing. Univ. Medellín, vol. 19, no. 36, pp. 223-237, Sep. 2019. https://doi.org/10.22395/rium.v19n36a11

D. Nelmangala Chandrashekhar, G. Girish Raj, and A. Gowda Nanjunda, “Properties and Application of Ablative Material,” Int. J. Eng. Res. Technol., vol. 10, no. 5, May. 2021. https://www.ijert.org/properties-and-application-of-ablative-material

M. Natali, J. M. Kenny, and L. Torre, “Science and technology of polymeric ablative materials for thermal protection systems and propulsion devices: A review,” Prog. Mater. Sci., vol. 84, pp. 192-275, Dec. 2016. https://doi.org/10.1016/j.pmatsci.2016.08.003

R. Robayo-Salazar, J. Portocarrero-Hermann, U. Díaz-Padrón, and O. Patiño-Castrillón, “Polymeric Ablative Composite Materials and their Application in the Manufacture of Aerospace Propulsion Components,” Rev. Fac. Ingen., vol. 29, no. 54, p. e10662, May. 2020. https://doi.org/10.19053/01211129.v29.n54.2020.10662

M. Natali, M. Monti, D. Puglia, J. M. Kenny, and L. Torre, “Ablative properties of carbon black and MWNT/phenolic composites: A comparative study,” Compos. Part A Appl. Sci. Manuf., vol. 43, no. 1, pp. 174-182, Jan. 2012. https://doi.org/10.1016/j.compositesa.2011.10.006

R. M. German, Particulate Composites Fundamentals and Applications. Berlin, GER: Springer, 2016. https://doi.org/10.1007/978-3-319-29917-4

F. C. Campbell, Structural Composite Materials. Russell, USA: ASM International, 2010. https://doi.org/10.31399/asm.tb.scm.9781627083140

R. Nakka, “Richard Nakka’s Experimental Rocketry Site,” rocketry.net, 2023. Accessed: Sep. 7, 2023. [Online]. Available: http://www.nakka-rocketry.net/

S. Farrukh, N. A. Tahir, A. Hussain, M. Ayoub, M. Rafiq, and M. H. Khan, “Fabrication and analysis of HNBR-Silica / Carbon Phenolic ablative composites as an effective thermal protection system (TPS),” in IOP Conf. Ser.: Mater. Sci. Engin., vol. 458. Kuala Lumpur, MY, Dec. 2018, p. 012015. https://doi.org/10.1088/1757-899X/458/1/012015

D. R. Askeland, P. P. Fulay, and W. J. Wright, Ciencia e ingeniería de materiales. México D. F., Mex: Cengage Learning, 2012. https://osvaldoweb.wordpress.com/wp-content/uploads/2016/04/ciencia-e-ingenieria-de-materiales-sexta-edicic3b3n.pdf

K. K. Chawla, Composite materials: Science and engineering, third edition. Berlin, GER: Springer Nature, 2012. https://link.springer.com/book/10.1007/978-3-030-28983-6

Y. Hou et al., “A novel ablative material for thermal protection system: Carbon fiber/polysiloxane composites,” Aerosp. Sci. Technol., vol. 129, p. 107822, Oct. 2022. https://doi.org/10.1016/j.ast.2022.107822

A. Eivaz Mohammadloo, M. Khorasani, H. Eivaz Mohammadloo, S. Roshan, R. Ghamsarizade, and A. A. Sarabi, “Dispersion stability, adhesion strength, and anti-corrosion properties of water-born polyester resins,” Mater. Chem. Phys., vol. 301, p. 127599, Jun. 2023. https://doi.org/10.1016/j.matchemphys.2023.127599

H. Qu et al., “Enhancing Thermal Insulation of EPDM Ablators via Constructing Alternating Planar Architectures,” Polymers, vol. 14, no. 8, Apr. 2022. https://doi.org/10.3390/polym14081570

S. L. Hu, Y. M. Li, W. J. Hu, J. Hobson, and D. Y. Wang, “Strategic design unsaturated polyester resins composites with excellent flame retardancy and high tensile strength,” Polym. Degrad. Stab., vol. 206, p. 110190, Dec. 2022. https://doi.org/10.1016/j.polymdegradstab.2022.110190

H. Cheng, Z. Fan, C. Hong, and X. Zhang, “Lightweight multiscale hybrid carbon-quartz fiber fabric reinforced phenolic-silica aerogel nanocomposite for high temperature thermal protection,” Compos. Part A Appl. Sci. Manuf., vol. 143, p.106313 Apr. 2021. https://doi.org/10.1016/j.compositesa.2021.106313

A. S. Alex, S. Bhuvaneswari, N. Sreenivas, V. Sekkar, and C. Gouri, “Short silica fibre-reinforced polymethylsilsesquioxane–phenolic interpenetrating networks: exploration for use as ablative thermal protection system in aerospace,” Polym. Bull., vol. 76, no. 8, pp. 3941-3956, Aug. 2019. https://doi.org/10.1007/s00289-018-2579-4

M. Natali, M. Monti, J. M. Kenny, and L. Torre, “A nanostructured ablative bulk molding compound: Development and characterization,” Compos. Part A Appl. Sci. Manuf., vol. 42, no. 9, pp. 1197-1204, Sep. 2011. https://doi.org/10.1016/j.compositesa.2011.04.022

How to Cite
[1]
V. Candela-Rengifo, R. Robayo-Salazar, J. Portocarrero Hermann, G. A. Rojas, and J. Salgado Díaz, “Design and Thermomechanical Evaluation of Polymer Matrix Ablative Composite Materials for Rocket Motor Nozzles”, TecnoL., vol. 28, no. 64, p. e3318, Nov. 2025.

Downloads

Download data is not yet available.
Published
2025-11-19
Section
Research Papers
Crossref Cited-by logo
Article metrics
Abstract views 439
Galley views 309
PDF Views 206
HTML views 29
Other views 74