Thermal isolation of steel pipelines employed in the transportation of hot fluids from thermal sprayed coatings
Abstract
Ceramic coatings of Al2O3, Al2O3-TiO2, and Al2O3-ZrO2 commercial powders were thermally sprayed on the external surface of ASTM A106 Grade-B carbon steel pipelines (with and without a bond coat of a commercial nickel alloy) to reduce the loss of heat contained in hot fluids that are transported through this kind of ducts. The bond coat, as well as the ceramic coatings, were deposited by means of oxy-acetylene thermal spray; afterwards, the heat transfer in transitory state was evaluated by placing heated silicone oil at 160°C inside the pipelines. The temperature variation over time of the silicone oil and the external wall of each pipeline was measured. Besides the low thermal conductivity of the ceramic materials, a thicker and more porous coating provides a more effective means for thermal isolation. Additionally, the bond coat acts as a thermal resistance, which consumes heat and contributes to the reduction of the superficial temperature of the pipeline.
References
MatWeb, “Online Materials Information Re-source - MatWeb”, 2016. [En línea]. Disponible en: http://www.matweb.com/. [Accedido: 03-ene-2016].
G. Latorre y F. Vargas, “Materiales compuestos reforzados con cerámicos amorfos para aplica-ciones a altas temperaturas”, CT&F Ciencia, Tecnol. y Futur., vol. 3, pp. 175-188, 2009.
G. Latorre y F. Vargas, “Nuevos Materiales, Materiales Compuestos, Tratamiento de superfi-cies”, Mater. Ing. - Ecopetrol, vol. 1, pp. 103-119, 2007.
Y. Başoğul y A. Keçebaş, “Economic and envi-ronmental impacts of insulation in district heat-ing pipelines”, Energy, vol. 36, no. 10, pp. 6156-6164, oct. 2011.
A. Bahadori y H. B. Vuthaluru, “A simple corre-lation for estimation of economic thickness of thermal insulation for process piping and equipment”, Appl. Therm. Eng., vol. 30, no. 2-3, pp. 254-259, feb. 2010.
J. Smith, William & Hashemi, Fundamentos de la ciencia e ingenieria de materiales, 4.a ed. México, 2006.
A. T. J. Verbeek, “Plasma Sprayed Thermal Barrier Coatings: Production, Characterization and Testing”, Technische Universiteit Eindho-ven, 1992.
S. Bose, “Chapter 7 – THERMAL BARRIER COATINGS (TBCs)”, en High Temperature Coat-ings, 2007, pp. 155-232.
I. D. Utu, G. Marginean, I. Hulka, V. A. Serban, y D. Cristea, “Properties of the thermally sprayed Al2O3–TiO2 coatings deposited on titanium substrate”, Int. J. Refract. Met. Hard Ma-ter., vol. 51, pp. 118-123, jul. 2015.
W. R. Chen, X. Wu, B. R. Marple, R. S. Lima, y P. C. Patnaik, “Pre-oxidation and TGO growth behaviour of an air-plasma-sprayed thermal barrier coating”, Surf. Coatings Technol., vol. 202, pp. 3787-3796, 2008.
E. Restrepo, F. Vargas, M. López, R. Cardona, y G. Duarte, “Elaboración de recubrimientos ce-rámicos mediante proyección térmica por com-bustión a partir de residuos sólidos industriales Elaboration of ceramic coatings by flame spra-ying process from industrial solid waste”, Rev. Mater., vol. 17 (4), pp. 1176-1185, 2012.
F. Vargas y G. Latorre, “Materiales de Ingenie-ría”, Ecopetrol, vol. 1, pp. 131-160, 2007.
M. Mellali, A. Grimaud, A. C. Leger, P. Fau-chais, y J. Lu, “Alumina grit blasting parame-ters for surface preparation in the plasma spray-ing operation”, J. Therm. Spray Technol., vol. 6, n.o 2, pp. 217-227, jun. 1997.
“Thermodynamic and Kinetic Data”, en CRC Materials Science and Engineering Handbook, Third Edition, CRC Press, 2000.
K. A. Habib, J. J. Saura, C. Ferrer, M. S. Damra, E. Giménez, y L. Cabedo, "Comparison of flame sprayed Al2O3/TiO2 coatings: Their microstruc-ture, mechanical properties and tribology behav-ior", Surf. Coatings Technol., vol. 201, n.o 3-4, pp. 1436-1443, oct. 2006.
W. D. Callister, Materials Science and Engineer-ing: An Introduction, 7.a ed. Estados Unidos: John Wiley & Sons, Inc., 2007.
A. G. González Hernández, “Estudio De La Influencia De Las Propiedades Físicas Y Mecá-nicas En El Comportamiento Tribológico De Re-cubrimientos Duros Para Herramientas De Cor-te Y Procesamiento De Polietileno”, Universidad de Antioquia, 2008.
J. E. Rodríguez, F. Vargas, E. López, E. Restre-po, and J. F. Gil, “Mejoramiento de la estructura de los recubrimientos de Al2o3-43% Tio2 elabo-rados mediante la técnica de proyección térmica por llama oxiacetilénica a partir de los paráme-tros de proyección,” Rev. Colomb. Mater., no. 5, pp. 120–126, 2014.
W. Conshohocken, “ASTM E1920 - Standard Guide for Metallographic Preparation of Ther-mal Sprayed Coatings”, ASM Int., vol. 3, n.o Re-approved 2014, pp. 1-5, 2014.
P. S. Santos, H. S. Santos, y S. P. Toledo, “Stan-dard transition aluminas. Electron microscopy studies”, Mater. Res., vol. 3, n.o 4, pp. 104-114, 2000.